Skip to content
All guides

Guides for av fleet operations managers

Vehicle out of service: the reason codes an AV fleet depot should use

A car held back from riders needs more than a red flag on the board. Nine reason codes, the line between a hard hold and a policy hold, a second field for what the car is waiting on, and how to mark, clear and count the cars that are held.

By XoomPark Editorial Team ·

Out of service means the car may not carry a rider until a named condition is fixed and signed off. The federal rule we use as the model forbids operating a motor vehicle in a condition likely to cause an accident or a breakdown,1 and bars anyone from operating a vehicle marked out of service until the required repairs are satisfactorily completed.2 A depot needs more than the yes or no: one reason code per car that says why it is out, a second field that says what it is waiting on, and a time in and a time out.
Nine reason codes for an AV fleet depot. The set and the letters are our suggestion, not a published standard; the basis column shows where each one borrows from a rule or a public definition.
CodeThe car is out becauseTypeCleared byBasis
SAFA defect likely to affect safe operation was found or reportedHardRepair, then a signed certification49 CFR 396.11;3 396.71
RCLThe VIN shows an unrepaired safety recallHardThe recall remedy, then a clean lookupNHTSA8
BRKIt cannot move, or cannot finish its tripHardRepair and a testThe transit database's major mechanical failure6
DMGCollision or body damageHard until inspectedRepair, or a documented releaseDepot policy (our assumption)
POLIt can drive, but depot policy keeps it backPolicyRepair, or a supervisor's releaseThe transit database's other mechanical failures6
PMScheduled maintenance is duePlannedWork order closed49 CFR 396.34
CLNContamination beyond the turnaround cleanPolicyCleaning sign-offDepot exposure plan (our assumption)
ADMRegistration, insurance or a permit has lapsedHardDocument on fileDepot policy (our assumption)
MKRThe vehicle's maker or its trained staff pulled the carHardThe maker's releaseMaker's procedure (our assumption)

What does out of service mean for an AV fleet car?

In the federal rules it is a formal status with a sticker. Authorized personnel declare and mark out of service any motor vehicle which, by reason of its mechanical condition or loading, would likely cause an accident or a breakdown.2 The Commercial Vehicle Safety Alliance describes its North American Standard Out-of-Service Criteria as the pass-fail criteria for inspections: critical violations render the driver, vehicle or cargo out of service until the condition is corrected.5

Two cautions before you borrow from them. The criteria are updated annually, effective April 1 of each year, so a copy pinned to the wall goes stale.5 And these rules were written for commercial motor vehicles; the inspection report rule, for one, does not apply to a private nonbusiness carrier of passengers, a driveaway-towaway operation or a carrier operating only one commercial motor vehicle.3 Whether they bind your cars is a question for your compliance lead. They are still the best public model of what a hold should mean.

A depot's own status is wider than the roadside one. It also covers cars that could drive but that you choose to keep back. It does not cover a car that is charging or in its turnaround clean: those are statuses on the way to ready, and counting them as out of service hides the cars that are really stuck.

Hard holds and policy holds: the split the National Transit Database uses

Split every hold into one of two kinds. The Federal Transit Administration's National Transit Database defines a major mechanical system failure as one that prevents a vehicle from completing a scheduled trip or starting the next one because actual movement is limited or because of safety concerns.6 It defines other mechanical system failures as ones that, because of local agency policy, prevent the trip even though the vehicle is physically able to continue in service.6

That line is worth copying. A hard hold is one nobody can talk their way past: a safety defect, an open recall, a car that will not move. A policy hold is a choice the depot made: a warning light you do not release with, a broken interior part, a scuffed panel. Our rule, an assumption and not a published standard: a hard hold is cleared only by the fix and its sign-off, while a policy hold can also be released by a named supervisor with a note on the record.

Report the two apart. Hours lost to hard holds are the price of safety. Hours lost to policy holds are a price you set yourself, and the only number on the board you can change by changing a rule.

Why a reason code and a waiting-on field are two different things

The reason says why the car came out. The waiting-on field says what is stopping it going back. "Awaiting parts" is not a reason; it is where a brake job is stuck today. Mix the two in one list and a car changes code every few hours, and nobody can say how long safety defects take to close. This two-field method is ours, an assumption and not a standard.
  • Waiting-on values we suggest: diagnosis, parts, a technician, a vendor or dealer, a bay, sign-off.
  • The reason code is set once, when the car comes out, and changes only if the diagnosis proves it wrong.
  • The waiting-on value changes as often as it needs to, and each change is time-stamped.
  • A third field holds the part or system, so "SAF, brakes, waiting on parts" reads as one line.

The trucking industry's coding standard works the same way. The American Trucking Associations' Technology & Maintenance Council says its Vehicle Maintenance Reporting Standards, developed in 1970, provide a single, concise coding convention, and the council is their official custodian.7 The standard keeps a separate code key for each question: Code Key 15, Work Accomplished, is a two-digit code for what the technician did, such as 02 Clean, 27 Align and 33 Tighten, and Code Key 18, Technician Failure Code, has over 90 codes for why a part failed, such as 10 Bent, 44 Worn and 60 Noisy.7 One field, one question. The council also says the level of coding used is entirely up to the user,7 which is why nine codes can be enough to start.

How do you mark a car out of service and bring it back?

Mark the car and the record at the same moment, and let only the fix remove the mark. Under the federal rule an "Out-of-Service Vehicle" sticker marks the vehicle, and no person may remove it before all the repairs required by the notice are complete.2 A depot tag on the car plus the status in the system does the same job: the board and the car can never disagree.
  • Who can place a hold: anyone who finds the condition. Who can clear it: only the role in the table above.
  • Moving a held car: the federal rule counts towing as operating, with one exception, that a marked vehicle may be towed away by a vehicle using a crane or hoist.2 Write your own yard-move rule for each hard code and print it on the tag.
  • A fault found on the road: a vehicle discovered to be unsafe may continue only to the nearest place where repairs can safely be made, and only if that is less hazardous to the public than leaving it on the highway.1
  • Coming back: before the vehicle is operated again, the carrier certifies that the defect has been repaired or that repair is unnecessary.3 Record who signed and when; that time is the car's time out.
  • After a roadside inspection: the carrier certifies within 15 days that all violations noted have been corrected, and keeps a copy for 12 months.2

Keep the history. The federal maintenance rule requires a record of inspection, repairs and maintenance showing their date and nature, plus a means to indicate the nature and due date of the work to come, kept for 1 year where the vehicle is housed or maintained and for 6 months after it leaves the carrier's control.4 Inspection reports and their repair certifications are kept three months.3 We suggest keeping the hold record with them, whichever rule applies to you.

How do you count out-of-service cars?

Against the whole roster, in car-hours, by code. A held car stays in the count: the National Transit Database's vehicles available for maximum service include operational vehicles, spares, out of service vehicles and vehicles in or awaiting maintenance, and leave out only vehicles awaiting sale and emergency contingency vehicles.6 Dropping held cars from the roster makes the rate look better and the yard look smaller than it is.

An example, with made-up numbers to show the arithmetic. A 60-car roster has 1,440 car-hours in a day. Two cars sit on safety holds all day (48 car-hours), one on a recall hold all day (24), three take 6 hours each for planned maintenance (18) and two sit 12 hours each on policy holds (24). That is 114 car-hours out of 1,440, an out-of-service rate of 7.9 percent. The policy holds are 24 of the 114, or 21 percent: the share you could win back without touching a wrench.

A car waiting on a charger is not in this count; it is a charging status. When stalls are what keep cars in the yard, XoomPark arranges AV fleet charging at existing stations in hours their stalls sit unused, never blocks a station's regular customers and never pushes a station past its monthly peak.

When reason codes are the wrong tool

  • An enforcement officer placed the vehicle out of service. The notice controls: the vehicle is not operated until every repair it requires is complete,2 whatever your own code says.
  • You need to know which part failed and how. That is part and failure coding, such as the Vehicle Maintenance Reporting Standards,7 sitting under the reason code, not replacing it.
  • The question is whether the driving system is fit to drive. That call belongs to the vehicle's maker and its trained staff; the MKR code only records that they made it.
  • You run a handful of cars. Our assumption: below about ten, a written list with a name beside each car does the same job.

Questions AV fleet operations managers ask

What does out of service mean for a vehicle?

In the federal rules, that authorized personnel have declared and marked it because its mechanical condition or loading would likely cause an accident or a breakdown.2 In a depot, any car held back from riders until a named condition is fixed and signed off.

What happens when a vehicle is placed out of service at a roadside inspection?

It is marked with an "Out-of-Service Vehicle" sticker and may not be operated until all repairs required by the notice are satisfactorily completed. The carrier then certifies within 15 days that the violations were corrected and keeps a copy for 12 months.2

Can a car be driven while it is out of service?

Not under the federal rule: nobody may operate a marked vehicle until the repairs are done, and towing counts as operating unless the tow vehicle uses a crane or hoist.2 For your own holds, write the yard-move rule for each code.

How many reason codes should a depot use?

Few enough to remember. We suggest the nine above, which is our assumption. The council that keeps the trucking industry's coding standard says the level of coding used is entirely up to the user,7 so add detail in the part field, not in more reasons.

Is a car waiting on a charger out of service?

No. Charging and the turnaround clean are statuses on the way to ready. Count them apart, or the board will hide the cars that are really stuck.

How do you know a recall hold is cleared?

When the remedy is done and NHTSA's lookup returns "0 unrepaired recalls associated with this VIN".8

Authorship

Written by XoomPark Editorial Team in collaboration with Claude Fable 5.2

Role breakdown: Topic selection and publishing by XoomPark Editorial Team; research, source checks against primary sources and draft prose by Claude Fable 5.2.